Summit Bearings, Where do I get them?

[Memphis Mud]

Unicycle.com doesn't carry them.

Since a Trials Unicycle is going to take a beating, I figure you
Trialsers have had to replace them a time or two. Where did you go?


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[iamthewaltrus]

I'm just gonna throw this out there, but you might try a bike shop.


--
iamthewaltrus - The Dynamic
------------------------------------------------------------------------
iamthewaltrus's Profile: http://www.unicyclist.com/profile/6274
View this thread: http://www.unicyclist.com/thread/34619

[iamthewaltrus]

I'm just gonna throw this out there, but you might try a bike shop.


--
iamthewaltrus - The Dynamic
------------------------------------------------------------------------
iamthewaltrus's Profile: http://www.unicyclist.com/profile/6274
View this thread: http://www.unicyclist.com/thread/34619

[iamthewaltrus]

I'm just gonna throw this out there, but you might try a bike shop.


--
iamthewaltrus - The Dynamic
------------------------------------------------------------------------
iamthewaltrus's Profile: http://www.unicyclist.com/profile/6274
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

Duaner (from Austin) found a local place that sells bearings of
different types. He was able to find one for a coker wheel. Maybe
there's a place like that in Memphis. Hopefully Duaner will respond
here with more details

-Eric


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

Duaner (from Austin) found a local place that sells bearings of
different types. He was able to find one for a coker wheel. Maybe
there's a place like that in Memphis. Hopefully Duaner will respond
here with more details

-Eric


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

Duaner (from Austin) found a local place that sells bearings of
different types. He was able to find one for a coker wheel. Maybe
there's a place like that in Memphis. Hopefully Duaner will respond
here with more details

-Eric


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

'try this link' (http://tinyurl.com/45bme)


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

'try this link' (http://tinyurl.com/45bme)


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

'try this link' (http://tinyurl.com/45bme)


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[john_childs]

'Boca Bearing' (http://www.bocabearings.com/) sells bearings online.

I believe the correct size for the KH is a 6004 (42mm outer diameter,
20mm inner diameter, 12mm width). You want the 6004-2RS. The 2RS means
that it has two rubber seals. A 6004-ZZ would have two metal seals.
Rubber seals work better for unicycles that are used outdoors a lot.

Use the search feature at the Boca Bearing web page and look for
bearings with a 42mm outer diameter and a 20mm inner diameter.

Here's a link to the 6004-2RS bearing in the Boca catalog: '6004-2RS'
(http://tinyurl.com/4nyk8)
$10.80 per bearing.


--
john_childs - Guinness Mojo

john_childs (at) hotmail (dot) com
Gallery: '' (http://www.unicyclist.com/gallery/john_childs)
------------------------------------------------------------------------
john_childs's Profile: http://www.unicyclist.com/profile/449
View this thread: http://www.unicyclist.com/thread/34619

[john_childs]

'Boca Bearing' (http://www.bocabearings.com/) sells bearings online.

I believe the correct size for the KH is a 6004 (42mm outer diameter,
20mm inner diameter, 12mm width). You want the 6004-2RS. The 2RS means
that it has two rubber seals. A 6004-ZZ would have two metal seals.
Rubber seals work better for unicycles that are used outdoors a lot.

Use the search feature at the Boca Bearing web page and look for
bearings with a 42mm outer diameter and a 20mm inner diameter.

Here's a link to the 6004-2RS bearing in the Boca catalog: '6004-2RS'
(http://tinyurl.com/4nyk8)
$10.80 per bearing.


--
john_childs - Guinness Mojo

john_childs (at) hotmail (dot) com
Gallery: '' (http://www.unicyclist.com/gallery/john_childs)
------------------------------------------------------------------------
john_childs's Profile: http://www.unicyclist.com/profile/449
View this thread: http://www.unicyclist.com/thread/34619

[john_childs]

'Boca Bearing' (http://www.bocabearings.com/) sells bearings online.

I believe the correct size for the KH is a 6004 (42mm outer diameter,
20mm inner diameter, 12mm width). You want the 6004-2RS. The 2RS means
that it has two rubber seals. A 6004-ZZ would have two metal seals.
Rubber seals work better for unicycles that are used outdoors a lot.

Use the search feature at the Boca Bearing web page and look for
bearings with a 42mm outer diameter and a 20mm inner diameter.

Here's a link to the 6004-2RS bearing in the Boca catalog: '6004-2RS'
(http://tinyurl.com/4nyk8)
$10.80 per bearing.


--
john_childs - Guinness Mojo

john_childs (at) hotmail (dot) com
Gallery: '' (http://www.unicyclist.com/gallery/john_childs)
------------------------------------------------------------------------
john_childs's Profile: http://www.unicyclist.com/profile/449
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Very good advice, all. Sarcasm or no.

I've spoken with several of the top b*ke shops and non of them seem know
what a unicycle is. Actually, they don't have difinitive answers on the
phone. Its a show and tell situation. The Summit is now in the trunk.

154 - that shop you linked is 1 mile from work. Thanks for pointing me
to my own back yard. I'll stop in today.

John - yours is excellent data I need to have. My old telephone line
connection was taking minutes to load your link, so I'll take a peek
when I get to work.

My biggest problem is I don't know nuthin bout no bearings. I suppose
its like everything else. You can get good ones or crappy ones. You
match up the diminsions and ba-da-bing your good to go? Maybe its just
that simple.

But I know I'll be smacking them again with this crank/pedal grab thing
I'm trying to learn. I think I landed hard on the little fellow and made
a slight oval out of what must necessarily by a perfect circle. A strong
argument could be made for getting an extra pair while I'm at it. My
learning curve is not as steep as it used to be.

Thanks again.

(I haven't been this excited about going to the office in ages!!)


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Very good advice, all. Sarcasm or no.

I've spoken with several of the top b*ke shops and non of them seem know
what a unicycle is. Actually, they don't have difinitive answers on the
phone. Its a show and tell situation. The Summit is now in the trunk.

154 - that shop you linked is 1 mile from work. Thanks for pointing me
to my own back yard. I'll stop in today.

John - yours is excellent data I need to have. My old telephone line
connection was taking minutes to load your link, so I'll take a peek
when I get to work.

My biggest problem is I don't know nuthin bout no bearings. I suppose
its like everything else. You can get good ones or crappy ones. You
match up the diminsions and ba-da-bing your good to go? Maybe its just
that simple.

But I know I'll be smacking them again with this crank/pedal grab thing
I'm trying to learn. I think I landed hard on the little fellow and made
a slight oval out of what must necessarily by a perfect circle. A strong
argument could be made for getting an extra pair while I'm at it. My
learning curve is not as steep as it used to be.

Thanks again.

(I haven't been this excited about going to the office in ages!!)


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Very good advice, all. Sarcasm or no.

I've spoken with several of the top b*ke shops and non of them seem know
what a unicycle is. Actually, they don't have difinitive answers on the
phone. Its a show and tell situation. The Summit is now in the trunk.

154 - that shop you linked is 1 mile from work. Thanks for pointing me
to my own back yard. I'll stop in today.

John - yours is excellent data I need to have. My old telephone line
connection was taking minutes to load your link, so I'll take a peek
when I get to work.

My biggest problem is I don't know nuthin bout no bearings. I suppose
its like everything else. You can get good ones or crappy ones. You
match up the diminsions and ba-da-bing your good to go? Maybe its just
that simple.

But I know I'll be smacking them again with this crank/pedal grab thing
I'm trying to learn. I think I landed hard on the little fellow and made
a slight oval out of what must necessarily by a perfect circle. A strong
argument could be made for getting an extra pair while I'm at it. My
learning curve is not as steep as it used to be.

Thanks again.

(I haven't been this excited about going to the office in ages!!)


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Very good advice, all. Sarcasm or no.

I've spoken with several of the top b*ke shops and non of them seem know
what a unicycle is. Actually, they don't have difinitive answers on the
phone. Its a show and tell situation. The Summit is now in the trunk.

154 - that shop you linked is 1 mile from work. Thanks for pointing me
to my own back yard. I'll stop in today.

John - yours is excellent data I need to have. My old telephone line
connection was taking minutes to load your link, so I'll take a peek
when I get to work.

My biggest problem is I don't know nuthin bout no bearings. I suppose
its like everything else. You can get good ones or crappy ones. You
match up the diminsions and ba-da-bing your good to go? Maybe its just
that simple.

But I know I'll be smacking them again with this crank/pedal grab thing
I'm trying to learn. I think I landed hard on the little fellow and made
a slight oval out of what must necessarily by a perfect circle. A strong
argument could be made for getting an extra pair while I'm at it. My
learning curve is not as steep as it used to be.

Thanks again.

(I haven't been this excited about going to the office in ages!!)


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Mr. Mud,

Does your Summit have shims around the bearings?

If not (no shims), do you have 43mm OD bearings?

If so (have shims), it would be interesting to know if a 43mm OD bearing
would fit and allow removal of the shim. I do not see a 43mm OD bearing
at the Boca Bearing site. Since you are in the market for new bearings,
could you ask about 43mm OD bearings if you shop locally and let us know
if they are available?

My Summit has bearing shims which are constantly coming loose and
sliding out of position. I sure would like to get rid of them if that is
possible. Based on other posts, there seems to be other Summit owners
out here who would like to know about this too.

Thanks


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Mr. Mud,

Does your Summit have shims around the bearings?

If not (no shims), do you have 43mm OD bearings?

If so (have shims), it would be interesting to know if a 43mm OD bearing
would fit and allow removal of the shim. I do not see a 43mm OD bearing
at the Boca Bearing site. Since you are in the market for new bearings,
could you ask about 43mm OD bearings if you shop locally and let us know
if they are available?

My Summit has bearing shims which are constantly coming loose and
sliding out of position. I sure would like to get rid of them if that is
possible. Based on other posts, there seems to be other Summit owners
out here who would like to know about this too.

Thanks


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Mr. Mud,

Does your Summit have shims around the bearings?

If not (no shims), do you have 43mm OD bearings?

If so (have shims), it would be interesting to know if a 43mm OD bearing
would fit and allow removal of the shim. I do not see a 43mm OD bearing
at the Boca Bearing site. Since you are in the market for new bearings,
could you ask about 43mm OD bearings if you shop locally and let us know
if they are available?

My Summit has bearing shims which are constantly coming loose and
sliding out of position. I sure would like to get rid of them if that is
possible. Based on other posts, there seems to be other Summit owners
out here who would like to know about this too.

Thanks


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Mr. Mud,

Does your Summit have shims around the bearings?

If not (no shims), do you have 43mm OD bearings?

If so (have shims), it would be interesting to know if a 43mm OD bearing
would fit and allow removal of the shim. I do not see a 43mm OD bearing
at the Boca Bearing site. Since you are in the market for new bearings,
could you ask about 43mm OD bearings if you shop locally and let us know
if they are available?

My Summit has bearing shims which are constantly coming loose and
sliding out of position. I sure would like to get rid of them if that is
possible. Based on other posts, there seems to be other Summit owners
out here who would like to know about this too.

Thanks


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

If you're looking to stock up you might consider 'this'
(http://tinyurl.com/5hr43).


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

If you're looking to stock up you might consider 'this'
(http://tinyurl.com/5hr43).


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

If you're looking to stock up you might consider 'this'
(http://tinyurl.com/5hr43).


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

If you're looking to stock up you might consider 'this'
(http://tinyurl.com/5hr43).


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

mucRider wrote:
> *Mr. Mud,
>
> Does your Summit have shims around the bearings?
>
> If not (no shims), do you have 43mm OD bearings?
>
> If so (have shims), it would be interesting to know if a 43mm OD
> bearing would fit and allow removal of the shim. I do not see a 43mm
> OD bearing at the Boca Bearing site. Since you are in the market for
> new bearings, could you ask about 43mm OD bearings if you shop locally
> and let us know if they are available?
>
> My Summit has bearing shims which are constantly coming loose and
> sliding out of position. I sure would like to get rid of them if that
> is possible. Based on other posts, there seems to be other Summit
> owners out here who would like to know about this too.
>
> Thanks *


From what I've been able to find from various bearing manufacturers is
that the OD for 20mm ID bearings can be any of the following:

20x32x7 (too small in both OD and width 7mm wide)
20x37x9 (too small both in OD and width 9mm wide)
20x42x8 (too small in width 8mm wide)
20x42x12 (these are the ones for summit but they're a touch too small in
OD)
20x47x14 (this overshoots the target in both OD and width)

So, that's probably why the summit uses shims. Apparently there is no
bearing made that is _exactly_ the right size.

-mg


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

mucRider wrote:
> *Mr. Mud,
>
> Does your Summit have shims around the bearings?
>
> If not (no shims), do you have 43mm OD bearings?
>
> If so (have shims), it would be interesting to know if a 43mm OD
> bearing would fit and allow removal of the shim. I do not see a 43mm
> OD bearing at the Boca Bearing site. Since you are in the market for
> new bearings, could you ask about 43mm OD bearings if you shop locally
> and let us know if they are available?
>
> My Summit has bearing shims which are constantly coming loose and
> sliding out of position. I sure would like to get rid of them if that
> is possible. Based on other posts, there seems to be other Summit
> owners out here who would like to know about this too.
>
> Thanks *


From what I've been able to find from various bearing manufacturers is
that the OD for 20mm ID bearings can be any of the following:

20x32x7 (too small in both OD and width 7mm wide)
20x37x9 (too small both in OD and width 9mm wide)
20x42x8 (too small in width 8mm wide)
20x42x12 (these are the ones for summit but they're a touch too small in
OD)
20x47x14 (this overshoots the target in both OD and width)

So, that's probably why the summit uses shims. Apparently there is no
bearing made that is _exactly_ the right size.

-mg


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

mucRider wrote:
> *Mr. Mud,
>
> Does your Summit have shims around the bearings?
>
> If not (no shims), do you have 43mm OD bearings?
>
> If so (have shims), it would be interesting to know if a 43mm OD
> bearing would fit and allow removal of the shim. I do not see a 43mm
> OD bearing at the Boca Bearing site. Since you are in the market for
> new bearings, could you ask about 43mm OD bearings if you shop locally
> and let us know if they are available?
>
> My Summit has bearing shims which are constantly coming loose and
> sliding out of position. I sure would like to get rid of them if that
> is possible. Based on other posts, there seems to be other Summit
> owners out here who would like to know about this too.
>
> Thanks *


From what I've been able to find from various bearing manufacturers is
that the OD for 20mm ID bearings can be any of the following:

20x32x7 (too small in both OD and width 7mm wide)
20x37x9 (too small both in OD and width 9mm wide)
20x42x8 (too small in width 8mm wide)
20x42x12 (these are the ones for summit but they're a touch too small in
OD)
20x47x14 (this overshoots the target in both OD and width)

So, that's probably why the summit uses shims. Apparently there is no
bearing made that is _exactly_ the right size.

-mg


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mgrant]

mucRider wrote:
> *Mr. Mud,
>
> Does your Summit have shims around the bearings?
>
> If not (no shims), do you have 43mm OD bearings?
>
> If so (have shims), it would be interesting to know if a 43mm OD
> bearing would fit and allow removal of the shim. I do not see a 43mm
> OD bearing at the Boca Bearing site. Since you are in the market for
> new bearings, could you ask about 43mm OD bearings if you shop locally
> and let us know if they are available?
>
> My Summit has bearing shims which are constantly coming loose and
> sliding out of position. I sure would like to get rid of them if that
> is possible. Based on other posts, there seems to be other Summit
> owners out here who would like to know about this too.
>
> Thanks *


From what I've been able to find from various bearing manufacturers is
that the OD for 20mm ID bearings can be any of the following:

20x32x7 (too small in both OD and width 7mm wide)
20x37x9 (too small both in OD and width 9mm wide)
20x42x8 (too small in width 8mm wide)
20x42x12 (these are the ones for summit but they're a touch too small in
OD)
20x47x14 (this overshoots the target in both OD and width)

So, that's probably why the summit uses shims. Apparently there is no
bearing made that is _exactly_ the right size.

-mg


--
mgrant - Ever hoping for the best!

The sun is the same in a relative way but you're older, shorter of
breath, and one day closer to death.
michael_j_grant (at) yahoo (dot) com
Gallery: http://www.unicyclist.com/gallery/Michael_Grant/
------------------------------------------------------------------------
mgrant's Profile: http://www.unicyclist.com/profile/440
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Who'da thought that when I took up unicycle riding, I would become so
educated regarding bearings?

MM - Never mind about the 43mm OD bearing.

MG - Thanks for the information. Based on your message, I did some more
research on my own. It does appear that the standard size is 42mm OD. In
the case of the Summit the 20x42x12 bearing is an industry standard
size. Prices range from $15 for a lot of 20 bearings on eBay to $78 for
a single high precision bearing of the same size at another site. There
is no standard 20x43x12 bearing.

I still wish I could find a 20x43x12 bearing just to see if it would
work.


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Who'da thought that when I took up unicycle riding, I would become so
educated regarding bearings?

MM - Never mind about the 43mm OD bearing.

MG - Thanks for the information. Based on your message, I did some more
research on my own. It does appear that the standard size is 42mm OD. In
the case of the Summit the 20x42x12 bearing is an industry standard
size. Prices range from $15 for a lot of 20 bearings on eBay to $78 for
a single high precision bearing of the same size at another site. There
is no standard 20x43x12 bearing.

I still wish I could find a 20x43x12 bearing just to see if it would
work.


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Who'da thought that when I took up unicycle riding, I would become so
educated regarding bearings?

MM - Never mind about the 43mm OD bearing.

MG - Thanks for the information. Based on your message, I did some more
research on my own. It does appear that the standard size is 42mm OD. In
the case of the Summit the 20x42x12 bearing is an industry standard
size. Prices range from $15 for a lot of 20 bearings on eBay to $78 for
a single high precision bearing of the same size at another site. There
is no standard 20x43x12 bearing.

I still wish I could find a 20x43x12 bearing just to see if it would
work.


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[mucRider]

Who'da thought that when I took up unicycle riding, I would become so
educated regarding bearings?

MM - Never mind about the 43mm OD bearing.

MG - Thanks for the information. Based on your message, I did some more
research on my own. It does appear that the standard size is 42mm OD. In
the case of the Summit the 20x42x12 bearing is an industry standard
size. Prices range from $15 for a lot of 20 bearings on eBay to $78 for
a single high precision bearing of the same size at another site. There
is no standard 20x43x12 bearing.

I still wish I could find a 20x43x12 bearing just to see if it would
work.


--
mucRider - Old Unicycling Newbie

Anything with more than one wheel is too complicated!
------------------------------------------------------------------------
mucRider's Profile: http://www.unicyclist.com/profile/6119
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

mgrant wrote:
> *If you're looking to stock up you might consider 'this'
> (http://tinyurl.com/5hr43). *


that sure looks like a great deal. after shipping that works out to
about $1.30 per bearing. has anyone used this type?

-eric


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

mgrant wrote:
> *If you're looking to stock up you might consider 'this'
> (http://tinyurl.com/5hr43). *


that sure looks like a great deal. after shipping that works out to
about $1.30 per bearing. has anyone used this type?

-eric


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

mgrant wrote:
> *If you're looking to stock up you might consider 'this'
> (http://tinyurl.com/5hr43). *


that sure looks like a great deal. after shipping that works out to
about $1.30 per bearing. has anyone used this type?

-eric


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[onefiftyfour]

mgrant wrote:
> *If you're looking to stock up you might consider 'this'
> (http://tinyurl.com/5hr43). *


that sure looks like a great deal. after shipping that works out to
about $1.30 per bearing. has anyone used this type?

-eric


--
onefiftyfour - Eric
------------------------------------------------------------------------
onefiftyfour's Profile: http://www.unicyclist.com/profile/3495
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Thanks to 154, I went to Memphis Bearing and Supply just a couple of
miles from my office. The bearings on the Summit say 6004zz. At present,
I don't know what bearings are in the box. But I suspect a dead match
because these guys know bearings.

They are 4.47 each. Cash transactions are No Refund, No Return. So, I
got a couple and will report later on how things are working.

Fringe Benefit: If you need bearings for your conveyor system or
submarine propellor, I know where to get them.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Thanks to 154, I went to Memphis Bearing and Supply just a couple of
miles from my office. The bearings on the Summit say 6004zz. At present,
I don't know what bearings are in the box. But I suspect a dead match
because these guys know bearings.

They are 4.47 each. Cash transactions are No Refund, No Return. So, I
got a couple and will report later on how things are working.

Fringe Benefit: If you need bearings for your conveyor system or
submarine propellor, I know where to get them.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Thanks to 154, I went to Memphis Bearing and Supply just a couple of
miles from my office. The bearings on the Summit say 6004zz. At present,
I don't know what bearings are in the box. But I suspect a dead match
because these guys know bearings.

They are 4.47 each. Cash transactions are No Refund, No Return. So, I
got a couple and will report later on how things are working.

Fringe Benefit: If you need bearings for your conveyor system or
submarine propellor, I know where to get them.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Thanks to 154, I went to Memphis Bearing and Supply just a couple of
miles from my office. The bearings on the Summit say 6004zz. At present,
I don't know what bearings are in the box. But I suspect a dead match
because these guys know bearings.

They are 4.47 each. Cash transactions are No Refund, No Return. So, I
got a couple and will report later on how things are working.

Fringe Benefit: If you need bearings for your conveyor system or
submarine propellor, I know where to get them.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[unibiker]

Mud,

Looks like I'm a little late, but I have had a lot of experience with
bearings. You can find better quality bearings at the bearing supply
stores like the one you found. And they're much cheaper.

My rule of thumb (from 30 years of experience):

Price the original replacement bearings.

Spend that same amount, or a bit more, at a bearing store, and usually
walk away with double sealed, high quality bearings that you will never
have to change again.

If you're gonna do the labor (which will provide good experience and
save $50-$70 per hour in labor charges) you can easily afford to buy the
best parts, and do the job ONCE.


--
unibiker - What is that thing anyway?

Jeff Baker


MAKE IT A GREAT DAY!!! > > > > 'Unibiker's Photo Gallery'
(http://www.unicyclist.com/gallery/albun01)
------------------------------------------------------------------------
unibiker's Profile: http://www.unicyclist.com/profile/473
View this thread: http://www.unicyclist.com/thread/34619

[unibiker]

Mud,

Looks like I'm a little late, but I have had a lot of experience with
bearings. You can find better quality bearings at the bearing supply
stores like the one you found. And they're much cheaper.

My rule of thumb (from 30 years of experience):

Price the original replacement bearings.

Spend that same amount, or a bit more, at a bearing store, and usually
walk away with double sealed, high quality bearings that you will never
have to change again.

If you're gonna do the labor (which will provide good experience and
save $50-$70 per hour in labor charges) you can easily afford to buy the
best parts, and do the job ONCE.


--
unibiker - What is that thing anyway?

Jeff Baker


MAKE IT A GREAT DAY!!! > > > > 'Unibiker's Photo Gallery'
(http://www.unicyclist.com/gallery/albun01)
------------------------------------------------------------------------
unibiker's Profile: http://www.unicyclist.com/profile/473
View this thread: http://www.unicyclist.com/thread/34619

[unibiker]

Mud,

Looks like I'm a little late, but I have had a lot of experience with
bearings. You can find better quality bearings at the bearing supply
stores like the one you found. And they're much cheaper.

My rule of thumb (from 30 years of experience):

Price the original replacement bearings.

Spend that same amount, or a bit more, at a bearing store, and usually
walk away with double sealed, high quality bearings that you will never
have to change again.

If you're gonna do the labor (which will provide good experience and
save $50-$70 per hour in labor charges) you can easily afford to buy the
best parts, and do the job ONCE.


--
unibiker - What is that thing anyway?

Jeff Baker


MAKE IT A GREAT DAY!!! > > > > 'Unibiker's Photo Gallery'
(http://www.unicyclist.com/gallery/albun01)
------------------------------------------------------------------------
unibiker's Profile: http://www.unicyclist.com/profile/473
View this thread: http://www.unicyclist.com/thread/34619

[unibiker]

Mud,

Looks like I'm a little late, but I have had a lot of experience with
bearings. You can find better quality bearings at the bearing supply
stores like the one you found. And they're much cheaper.

My rule of thumb (from 30 years of experience):

Price the original replacement bearings.

Spend that same amount, or a bit more, at a bearing store, and usually
walk away with double sealed, high quality bearings that you will never
have to change again.

If you're gonna do the labor (which will provide good experience and
save $50-$70 per hour in labor charges) you can easily afford to buy the
best parts, and do the job ONCE.


--
unibiker - What is that thing anyway?

Jeff Baker


MAKE IT A GREAT DAY!!! > > > > 'Unibiker's Photo Gallery'
(http://www.unicyclist.com/gallery/albun01)
------------------------------------------------------------------------
unibiker's Profile: http://www.unicyclist.com/profile/473
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Post Operative Briefing:

The operation is so easy its rediculous. We used Tommy's bearing puller
because we thought we had to. The thing slid off effortlessly. New one
in. Good to go.

How easy.

Bearings: 20 x 42 x 12
I'm using 6004zz because thats what was on in the first place and thats
what the Bearing store replaced them with.

Cost: 4.47 per bearing.

The disection of the Summit confirmed that the problem was my crank
grabbing technique. I landed hard on that bearing cover and have bend it
imperceptively, but enough to rub things wrong.

To repeat, with the Summit at least, you take the crank off (easy), pull
off dust covers and shim (easy), pull off old bearings (easy), slip on
new bearings (easy), put everything back together (easy), ride away
happy.

If you can change the lightbulb in a flashlight, you can perform this
operation.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Post Operative Briefing:

The operation is so easy its rediculous. We used Tommy's bearing puller
because we thought we had to. The thing slid off effortlessly. New one
in. Good to go.

How easy.

Bearings: 20 x 42 x 12
I'm using 6004zz because thats what was on in the first place and thats
what the Bearing store replaced them with.

Cost: 4.47 per bearing.

The disection of the Summit confirmed that the problem was my crank
grabbing technique. I landed hard on that bearing cover and have bend it
imperceptively, but enough to rub things wrong.

To repeat, with the Summit at least, you take the crank off (easy), pull
off dust covers and shim (easy), pull off old bearings (easy), slip on
new bearings (easy), put everything back together (easy), ride away
happy.

If you can change the lightbulb in a flashlight, you can perform this
operation.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Post Operative Briefing:

The operation is so easy its rediculous. We used Tommy's bearing puller
because we thought we had to. The thing slid off effortlessly. New one
in. Good to go.

How easy.

Bearings: 20 x 42 x 12
I'm using 6004zz because thats what was on in the first place and thats
what the Bearing store replaced them with.

Cost: 4.47 per bearing.

The disection of the Summit confirmed that the problem was my crank
grabbing technique. I landed hard on that bearing cover and have bend it
imperceptively, but enough to rub things wrong.

To repeat, with the Summit at least, you take the crank off (easy), pull
off dust covers and shim (easy), pull off old bearings (easy), slip on
new bearings (easy), put everything back together (easy), ride away
happy.

If you can change the lightbulb in a flashlight, you can perform this
operation.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619

[Memphis Mud]

Post Operative Briefing:

The operation is so easy its rediculous. We used Tommy's bearing puller
because we thought we had to. The thing slid off effortlessly. New one
in. Good to go.

How easy.

Bearings: 20 x 42 x 12
I'm using 6004zz because thats what was on in the first place and thats
what the Bearing store replaced them with.

Cost: 4.47 per bearing.

The disection of the Summit confirmed that the problem was my crank
grabbing technique. I landed hard on that bearing cover and have bend it
imperceptively, but enough to rub things wrong.

To repeat, with the Summit at least, you take the crank off (easy), pull
off dust covers and shim (easy), pull off old bearings (easy), slip on
new bearings (easy), put everything back together (easy), ride away
happy.

If you can change the lightbulb in a flashlight, you can perform this
operation.


--
Memphis Mud - Student of GrandMaster 2T

Mantra: Avoid Hitting Tailbone...Avoid Hitting Tailbone...

"do not think, just ride"...muniracer
------------------------------------------------------------------------
Memphis Mud's Profile: http://www.unicyclist.com/profile/1987
View this thread: http://www.unicyclist.com/thread/34619