|
|
Ahh! PITA tubulars and old bikes by
Phil, Squid-in-Training
Wow. So talk about me being a dumbass. Here's the chronology:
1. Friend 1 talks about being interested in road bike
2. Friend 1 and I go get an old road...
|
|
6 |
1,296 |
|
|
|
|
5 |
581 |
|
|
|
|
2 |
647 |
|
|
Do underweight rims warp? by
Phil, Squid-in-Training
I built up a stupid-light 1420g MTB disc/v-brake wheelset using Sun UFO
rims. They're a 395g claimed weight, but they ended up being 360g each,
about a 10%...
( 1 2 3)
|
|
22 |
994 |
|
|
Saddle position on XS frames by
Phil, Squid-in-Training
As I become a more experienced road and mountain rider, I find myself more
and more comfortable on smaller and smaller bikes. At 5'5" with a 29.5"
inseam, I...
|
|
3 |
343 |
|
|
Pedal cones and locknuts: how to tighten? by
Phil, Squid-in-Training
On the majority of pedals, there's a nylock locknut and the outer cone nut.
How do you tighten them against each other? It's like I'd need two sockets,
one...
( 1 2)
|
|
13 |
575 |
|
|
Bike Stopping distances? by
Phil, Squid-in-Training
Bob wrote:
Looking for a chart with bike stopping distances. Perhaps there's
something out there where they compared brake types, pads, tires,
etc -...
|
|
3 |
1,050 |
|
|
How long do race wheels last? by
Phil, Squid-in-Training
Mike wrote:
I have just purchased a set of Mavic SL race wheels.
I am reasonable new to the sport and wondered why most people only
get their good...
|
|
4 |
374 |
|
|
Preferred BB tool? by
Phil, Squid-in-Training
What do you guys use to crank down/up on botton bracket sockets? Namely,
the ones with ~30mm hex flats? I bought a 24" adjustable wrench that works,
but at...
( 1 2 3 ... Last Page)
|
|
34 |
1,036 |
|
|
Tubeless road tires idea by
Phil, Squid-in-Training
Would anybody feel comfortable converting a road tire to tubeless w/slime?
Other than a higher air diffusion rate than with tubes, there doesn't seem
to be a...
|
|
6 |
655 |
|
|
|
|
6 |
1,331 |
|
|
Upgrading from DT to STI, 7 to 8 speed by
Phil, Squid-in-Training
I'm contemplating upgrading my 7-speed DT to 8 speed STI.
I believe some RSX shifters were 7-speed, but it seems most were 8. If I go
this route, I would...
|
|
4 |
1,399 |
|
|
Easy way to calculate grade? by
Phil, Squid-in-Training
There's a hill nearby whose gradient or whatever I'd like to guess. How
should I go about it? I don't have any surveying equipment, and my GPS is
long gone. ...
( 1 2 3 ... Last Page)
|
|
82 |
1,994 |
|
|
BB antiseize doesn't work? by
Phil, Squid-in-Training
My Giant STP2 came with completely dry BB cups (Truvativ ISIS), and I had
ridden it for about 6 months before enough wet rides had penetrated it and
caused it...
( 1 2)
|
|
13 |
509 |
|
|
Airless tire impressions by
Phil, Squid-in-Training
Somebody mentioned that a company was sending free 1-inch long samples of
their airless tires. I got mine in the mail last week. Here are...
|
|
2 |
875 |
|
|
Kool-Stop MTB Salmon brake pad weakness by
Phil, Squid-in-Training
The stupid "angled tip and plow" on the leading edge of the brake pad is
positively uesless. I put them on the front expecting them to increase
power over my...
|
|
4 |
715 |
|
|
|
|
51 |
1,261 |
|
|
Sad fork story update by
Phil, Squid-in-Training
Here are two pictures of the damage wrought:
1. This is my attempt at relieving stress at the expanded part of the
steerer near the bottom. Since that wasn't...
|
|
3 |
319 |
|
|
|
February 6th 05 10:40 PM
by A Muzi
|
17 |
1,126 |
|
|
Handlebar vibration damping question by
Phil, Squid-in-Training
This post is actually in reference to a motorcycle, not a bicycle, but the
principles are the same.
My Honda CBR600 F2 is buzzy as hell from the engine...
( 1 2)
|
February 21st 06 06:58 AM
by Sorni
|
15 |
719 |