|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
which multi-tool is best?
I broke my Kool Tool, and they don't seem to be available anymore - though i'd be pleased to hear otherwise. (I deserved it - i was trying to undo a cross threaded pedal with the Kool Tool adjustable spanner and a 12" adjustable for more leverage - the adjustable bit of the jaw broke off. But I was desperate at the time) So what's the best minimal but adequate tool out there? Requirements would be at least chain tool, pedal spanner, usual allen keys, cross and flat screwdriver and some kind of sockets/spanner capability. Topeak Alien II looks promising but rather expensive. cheers. |
Ads |
#2
|
|||
|
|||
On 24 Jan 2005 09:48:23 -0800, "rob crompton"
wrote: I broke my Kool Tool, and they don't seem to be available anymore - though i'd be pleased to hear otherwise. (I deserved it - i was trying to undo a cross threaded pedal with the Kool Tool adjustable spanner and a 12" adjustable for more leverage - the adjustable bit of the jaw broke off. But I was desperate at the time) So what's the best minimal but adequate tool out there? Requirements would be at least chain tool, pedal spanner, usual allen keys, cross and flat screwdriver and some kind of sockets/spanner capability. Topeak Alien II looks promising but rather expensive. I'm not a fan of purpose built multi-tools, I think they are a triumph of marketing over function. To my mind you're better off putting together your own custom cluster of tiny bits. With careful choice you'll end up with far superior tools that take up no more space than an all in one (in fact, they can be easier to cram into small packs because they're individual elements, not one single lump.) You can also take only what you need, and nothing extra, as is the case with most multi-tools. I carry a Facom 1/4" drive sliding T, a small 50mm extension and a bit adapter with a selection of hex and screwdriver bits. See he http://homepage.ntlworld.com/gareth..../MiniTool2.jpg http://homepage.ntlworld.com/gareth..../MiniTool1.jpg I promise you these will take *way* more abuse than an Alien without letting you down, and given your pedal extraction technique described above, it sounds like you need reliability There's a 50p piece there for scale, and the seatpack is the smallest in the Topeak range, just enough room for an innertube with a few tools on top. That's a very small bundle, and very flexible too. Carry just the appropriate size bits for the bike you are on and if you want socket capability too, throw in a couple of 1/4" drive sockets as well. You'll need a compact stand alone chain tool, but these are widely available. Just having had a look, I'm wondering if this head unit could be made to work with a T bar and extension: http://tinyurl.com/46aop Might make a super compact option, and only 20 grams. Your other requirement is a pedal spanner, but I think you're asking a lot here from a portable tool. That's about the nastiest union on a bike, and almost anything you carry along is going to struggle if the pedal decides to be a *******. As long as the threads were greased when installed, and not left to seize for months on end, then you should be able to do most pedals with the T bar and hex head bit (assuming good quality tools). Other than that your best option is maybe a 6" adjustable... but I wouldn't want to lug one around. Anyway, that's my suggestion as an alternative to a multi-tool, make yer own. -- Call me "Bob" "More oneness, less categories, Open hearts, no strategies" Email address is spam trapped, to reply directly remove the beverage. |
#3
|
|||
|
|||
Call me Bob wrote:
On 24 Jan 2005 09:48:23 -0800, "rob crompton" wrote: I broke my Kool Tool, and they don't seem to be available anymore - though i'd be pleased to hear otherwise. (I deserved it - i was trying to undo a cross threaded pedal with the Kool Tool adjustable spanner and a 12" adjustable for more leverage - the adjustable bit of the jaw broke off. But I was desperate at the time) So what's the best minimal but adequate tool out there? Requirements would be at least chain tool, pedal spanner, usual allen keys, cross and flat screwdriver and some kind of sockets/spanner capability. Topeak Alien II looks promising but rather expensive. Try and do without a pedal spanner, Rob. I'm not a fan of purpose built multi-tools, I think they are a triumph of marketing over function. To my mind you're better off putting together your own custom cluster of tiny bits. With careful choice you'll end up with far superior tools that take up no more space than an all in one (in fact, they can be easier to cram into small packs because they're individual elements, not one single lump.) You can also take only what you need, and nothing extra, as is the case with most multi-tools. Tend to agree, although it doesn't stop me thinking about buying one each time I see one :-) I carry a Facom 1/4" drive sliding T, a small 50mm extension and a bit adapter with a selection of hex and screwdriver bits. See he http://homepage.ntlworld.com/gareth..../MiniTool2.jpg http://homepage.ntlworld.com/gareth..../MiniTool1.jpg Not as heavy-duty or versatile but the Topeak ToolBar is lighter and its head will take standard 1/4" bits and sockets with an adapter. It's rather neat & comfortable, I like it. Only half-length bits can be stored inside the body, though. ~PB |
#4
|
|||
|
|||
On Mon, 24 Jan 2005 20:30:39 -0000, "Pete Biggs"
wrote: I'm not a fan of purpose built multi-tools Tend to agree, although it doesn't stop me thinking about buying one each time I see one :-) Tools, innit. We are powerless in the face of their shiny glare. -- Call me "Bob" "More oneness, less categories, Open hearts, no strategies" Email address is spam trapped, to reply directly remove the beverage. |
#5
|
|||
|
|||
in message .com, rob
crompton ') wrote: I broke my Kool Tool, and they don't seem to be available anymore - though i'd be pleased to hear otherwise. (I deserved it - i was trying to undo a cross threaded pedal with the Kool Tool adjustable spanner and a 12" adjustable for more leverage - the adjustable bit of the jaw broke off. But I was desperate at the time) So what's the best minimal but adequate tool out there? Requirements would be at least chain tool, pedal spanner, usual allen keys, cross and flat screwdriver and some kind of sockets/spanner capability. Topeak Alien II looks promising but rather expensive. I have the Alien, it's a very nice and useful piece of kit. With an Alien, a crank tool and a cone spanner you can completely strip a bike; I often use it in in my workshop in preference to getting the toolbox out. However Edinburgh Bike Co-op sell a clone of it - in two separate pieces presumably to avoid Topeak's patents - for very much less: the 'Lifu Pocket 12' and 'Lifu Pocket 7' for twenty-one quid the pair. Allegedly these snap together like the two halves of the Alien. I can't comment on their quality. The Co-op also offers the Specialized EMT Comp for twenty quid which is a known brand and reasonable quality. I have one of these, too - but I prefer the Alien. It's expensive, but it's worth it. -- (Simon Brooke) http://www.jasmine.org.uk/~simon/ -----BEGIN GEEK CODE BLOCK----- Version: 3.1 GP/CS s++: a+ C+++ ULBVCS*++++$ L+++ P--- E+++ W+++ N++ K w--(---) M- !d- PS++ PE-- Y+ PGP !t 5? X+ !R b++ !DI D G- e++ h*(-) r++ y+++ ------END GEEK CODE BLOCK------ |
#6
|
|||
|
|||
Call me Bob wrote:
I carry a Facom 1/4" drive sliding T, a small 50mm extension and a bit adapter with a selection of hex and screwdriver bits. See he http://homepage.ntlworld.com/gareth..../MiniTool2.jpg Ooh, tidy. Do you remember where you got it? -- jc Remove the -not from email |
#7
|
|||
|
|||
On Tue, 25 Jan 2005 08:58:09 GMT, Jeremy Collins
wrote: I carry a Facom 1/4" drive sliding T, a small 50mm extension and a bit adapter with a selection of hex and screwdriver bits. See he http://homepage.ntlworld.com/gareth..../MiniTool2.jpg Ooh, tidy. Do you remember where you got it? They're standard hand tools, you'll get them from any good tool store. If you want those particularly then get out the yellow pages and find your local Facom dealer, the part numbers a T bar R120 50mm ext R209 Bit holder R235 Should be about £20 altogether, with VAT and a bit of discount. You could save a few quid by purchasing a different brand, but then Facom 1/4" drive stuff is the best quality available and will last you the rest of your life. You'll find too that other brands are slightly fatter and heavier in the hand (and seat pack), perhaps important to you. -- Call me "Bob" "More oneness, less categories, Open hearts, no strategies" Email address is spam trapped, to reply directly remove the beverage. |
#8
|
|||
|
|||
Call me Bob wrote:
On Tue, 25 Jan 2005 08:58:09 GMT, Jeremy Collins wrote: I carry a Facom 1/4" drive sliding T, a small 50mm extension and a bit adapter with a selection of hex and screwdriver bits. See he http://homepage.ntlworld.com/gareth..../MiniTool2.jpg Ooh, tidy. Do you remember where you got it? They're standard hand tools, you'll get them from any good tool store. If you want those particularly then get out the yellow pages and find your local Facom dealer, the part numbers a T bar R120 50mm ext R209 Bit holder R235 Should be about £20 altogether, with VAT and a bit of discount. You could save a few quid by purchasing a different brand, but then Facom 1/4" drive stuff is the best quality available and will last you the rest of your life. You'll find too that other brands are slightly fatter and heavier in the hand (and seat pack), perhaps important to you. Thanks for the info. My local B&Q doesn't have such things, or I certainly would have got one by now. I searched Screwfix without luck too. I'll ask at my local hardware shop, which is eye-wateringly expensive but has good staff who can probably help me get one. I usually carry a key-ring thing full of standard allen keys, which is a bit cumbersome, plus I have to share them between my cycle bag and toolbox, so they're often in the wrong place. -- jc Remove the -not from email |
#9
|
|||
|
|||
In article , Call me Bob wrote:
On 24 Jan 2005 09:48:23 -0800, "rob crompton" wrote: [...] That's a very small bundle, and very flexible too. Carry just the appropriate size bits for the bike you are on and if you want socket capability too, throw in a couple of 1/4" drive sockets as well. You'll need a compact stand alone chain tool, but these are widely available. And a spoke key (and possibly a knife and bottle opener to match the Alien). (The Alien does have a little pedal spanner too, but I have serious doubts about whether it would handle a remotely stuck pedal, so long as your pedals can be done with a hex bit instead that's almost certainly a better bet). |
#10
|
|||
|
|||
On 24 Jan 2005 09:48:23 -0800, "rob crompton"
wrote: So what's the best minimal but adequate tool out there? Slightly more minimalist than your reqs but I like the crank bros multitools - they're reasonably light but strong, the chain tool is exvellent (I use it as my main chain splitter). I bought mine from Cyclexpres, post free: http://www.cyclexpress.co.uk/product...7_Tool_664.asp cheers, tom. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Park Tool Sox | jerryo | Marketplace | 0 | December 7th 04 05:44 PM |
FS: Park Tool Brake Third Hand Tool, $5 shipped | Rob Barnes | Marketplace | 1 | June 11th 04 03:11 AM |
FA: Campagnolo Freewheel Tool Kit | The Ink Company | Marketplace | 0 | September 23rd 03 03:09 AM |
Gift certificates, tool selection, toy selection [2nd try] | Rick Onanian | Techniques | 11 | September 18th 03 04:23 AM |
mutant cassette lockring tool | g.daniels | Techniques | 4 | July 11th 03 04:38 PM |