|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Jan Heine on wheel building
https://janheine.wordpress.com
Today's blog post is about building strong wheels. -- - Frank Krygowski |
Ads |
#2
|
|||
|
|||
Jan Heine on wheel building
On Tuesday, March 14, 2017 at 7:51:48 AM UTC-7, Frank Krygowski wrote:
https://janheine.wordpress.com Today's blog post is about building strong wheels. -- - Frank Krygowski That guy is just such a doof it's impossible to take him seriously even when what he's saying is not incorrect. |
#3
|
|||
|
|||
Jan Heine on wheel building
On 2017-03-14, Doug Landau wrote:
On Tuesday, March 14, 2017 at 7:51:48 AM UTC-7, Frank Krygowski wrote: https://janheine.wordpress.com That guy is just such a doof it's impossible to take him seriously even when what he's saying is not incorrect. Try. It's good for you. -- Gregory S. Sutter Mostly Harmless http://zer0.org/~gsutter/ |
#4
|
|||
|
|||
Jan Heine on wheel building
On Tuesday, March 14, 2017 at 9:51:48 AM UTC-5, Frank Krygowski wrote:
https://janheine.wordpress.com Today's blog post is about building strong wheels. -- - Frank Krygowski Almost all of it was just simple common sense. Nothing contentious. But this sentence from the article was a bit odd: "For each of these rim/hub combinations, we now offer spoke packages with the highest-quality, double-butted, superlight Sapim Laser spokes (2.0 – 1.5 – 2.0 mm) and aluminum nipples." I understand his explanation of detensioning the spokes on every revolution and the thin spokes stretch more to prevent some of the detensioning. But going with $1 a piece Laser spokes of 14/17 gauge instead of the cheaper 50 cents a piece and readily available 15/14 double butted spokes from DT or Sapim. Aluminum nipples? I thought brass was the standard for reliability. Never rounds off or breaks ever. |
#5
|
|||
|
|||
Jan Heine on wheel building
On Tue, 14 Mar 2017 10:51:45 -0400, Frank Krygowski
wrote: https://janheine.wordpress.com Today's blog post is about building strong wheels. He seems to ignore the upper spokes. If the bottom spokes become unloaded ( looser) then, logically, the top spokes must become more highly loaded (tighter) :-) -- Cheers, John B. |
#7
|
|||
|
|||
Jan Heine on wheel building
On Tuesday, March 14, 2017 at 5:49:54 PM UTC-7, John B. wrote:
On Tue, 14 Mar 2017 10:51:45 -0400, Frank Krygowski wrote: https://janheine.wordpress.com Today's blog post is about building strong wheels. He seems to ignore the upper spokes. If the bottom spokes become unloaded ( looser) then, logically, the top spokes must become more highly loaded (tighter) :-) Are you -sure- you want to say that on this group? |
#8
|
|||
|
|||
Jan Heine on wheel building
John B. wrote:
On Tue, 14 Mar 2017 10:51:45 -0400, Frank Krygowski wrote: https://janheine.wordpress.com Today's blog post is about building strong wheels. He seems to ignore the upper spokes. If the bottom spokes become unloaded ( looser) then, logically, the top spokes must become more highly loaded (tighter) :-) -- Cheers, John B. It's a bit asymmetrical. If the rim was very "floppy", then only one spoke at a time on the bottom would be detensioned, but a large number of upper spokes would share the increase. As the rim gets stiffer and stiffer, then the detensioning of the lower spokes gets more uniform and smaller. In the ultimate case of a perfectly stiff rim, then the loss of tension in the lower spikes would be perfectly and symmetrically compensated by an increase in tension of the upper spokes. So you can leave less upward margin in your spoke tension than you have to leave on the downward side. |
#9
|
|||
|
|||
Jan Heine on wheel building
On 15/03/17 11:01, wrote:
On Tuesday, March 14, 2017 at 9:51:48 AM UTC-5, Frank Krygowski wrote: https://janheine.wordpress.com Today's blog post is about building strong wheels. -- - Frank Krygowski Almost all of it was just simple common sense. Nothing contentious. But this sentence from the article was a bit odd: "For each of these rim/hub combinations, we now offer spoke packages with the highest-quality, double-butted, superlight Sapim Laser spokes (2.0 – 1.5 – 2.0 mm) and aluminum nipples." I understand his explanation of detensioning the spokes on every revolution and the thin spokes stretch more to prevent some of the detensioning. But going with $1 a piece Laser spokes of 14/17 gauge instead of the cheaper 50 cents a piece and readily available 15/14 double butted spokes from DT or Sapim. Aluminum nipples? I thought brass was the standard for reliability. Never rounds off or breaks ever. I was wondering about the Al nipples too. -- JS |
#10
|
|||
|
|||
Jan Heine on wheel building
On 15/03/17 11:49, John B. wrote:
On Tue, 14 Mar 2017 10:51:45 -0400, Frank Krygowski wrote: https://janheine.wordpress.com Today's blog post is about building strong wheels. He seems to ignore the upper spokes. If the bottom spokes become unloaded ( looser) then, logically, the top spokes must become more highly loaded (tighter) :-) Not so much. -- JS |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Heine on inflation | AMuzi | Techniques | 70 | April 19th 16 12:12 AM |
Jan Heine on headlights | Frank Krygowski[_2_] | Techniques | 2 | September 29th 13 01:46 AM |
Kickin a little (Jan) Heine | ceecee | Techniques | 1 | July 2nd 10 03:00 PM |
WHEEL BUILDING 273 | datakoll | Techniques | 2 | January 11th 08 08:54 AM |
Building a BC Wheel - Help! | galvin.ben | Unicycling | 14 | July 30th 07 03:06 AM |