A Cycling & bikes forum. CycleBanter.com

Go Back   Home » CycleBanter.com forum » rec.bicycles » Techniques
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

A hole in the stem



 
 
Thread Tools Display Modes
  #1  
Old April 13th 19, 04:15 AM posted to rec.bicycles.tech
Joy Beeson
external usenet poster
 
Posts: 1,638
Default A hole in the stem



I don't recall whether my handlebars came with the Raleigh Carleton or
the Fugi Grand Tourer -- we swapped components rather suddenly when a
mechanic overhauling the Raleigh found a defect in the brake bridge
that was above his pay grade. I don't think I ever knew whether the
handlebars and stems were included in the swap; we just left both
bikes with the mechanic.

It says "GB" in a circle in a recessed diamond on the stem.

Just above the point of the diamond, an adjusting barrel for the front
brake cable is set in the top of a hole through the stem.

I read somewhere that drilling a hole through the stem is a terrible,
horrible idea, and it makes sense that one should avoid weakening such
a vital component, but it's a tempting idea: It looks neater, it
makes the path of the cable slightly smoother, and it makes the cable
a more convenient place to hang my gloves.

So as long as the hole is there I might as well use it, but the
mechanic at the Trailhouse routes the cable around the stem, as if
there were no hole.

I'm going to have the bike overhauled pretty soon, and I'm thinking of
telling him to use the hole -- but is there some *other* reason why
routing a brale cable through the stem is a bad idea?

--
joy beeson at comcast dot net
http://wlweather.net/PAGESEW/
The above message is a Usenet post.
I don't recall having given anyone permission to use it on a Web site.


  #2  
Old April 13th 19, 05:20 AM posted to rec.bicycles.tech
jOHN b.
external usenet poster
 
Posts: 2,421
Default A hole in the stem

On Fri, 12 Apr 2019 23:15:03 -0400, Joy Beeson
wrote:



I don't recall whether my handlebars came with the Raleigh Carleton or
the Fugi Grand Tourer -- we swapped components rather suddenly when a
mechanic overhauling the Raleigh found a defect in the brake bridge
that was above his pay grade. I don't think I ever knew whether the
handlebars and stems were included in the swap; we just left both
bikes with the mechanic.

It says "GB" in a circle in a recessed diamond on the stem.

Just above the point of the diamond, an adjusting barrel for the front
brake cable is set in the top of a hole through the stem.

I read somewhere that drilling a hole through the stem is a terrible,
horrible idea, and it makes sense that one should avoid weakening such
a vital component, but it's a tempting idea: It looks neater, it
makes the path of the cable slightly smoother, and it makes the cable
a more convenient place to hang my gloves.

So as long as the hole is there I might as well use it, but the
mechanic at the Trailhouse routes the cable around the stem, as if
there were no hole.

I'm going to have the bike overhauled pretty soon, and I'm thinking of
telling him to use the hole -- but is there some *other* reason why
routing a brale cable through the stem is a bad idea?


I suppose that drilling a hole in part of the steering may be
considered as a poor idea but on the other hand if you have been
riding the bike for a long time with no problems I might be inclined
not to worry about it too much.

Of course, handle bar stems are not exactly what one would term
"expensive". Amazon lists a "Big Roc 57SYC80PK Handle Bar Stem, 22.2 x
80 x 145mm, Alloy" for $15.55 (in pink) and a Sunlite Adjustable Quill
Stem, 22.2 x 90 x 180mm, Silver for $19.95, or contact Andrew Muzi for
(perhaps) a better quote.
--
cheers,

John B.

  #3  
Old April 13th 19, 11:58 AM posted to rec.bicycles.tech
Sir Ridesalot
external usenet poster
 
Posts: 5,270
Default A hole in the stem

On Friday, April 12, 2019 at 11:15:09 PM UTC-4, Joy Beeson wrote:
I don't recall whether my handlebars came with the Raleigh Carleton or
the Fugi Grand Tourer -- we swapped components rather suddenly when a
mechanic overhauling the Raleigh found a defect in the brake bridge
that was above his pay grade. I don't think I ever knew whether the
handlebars and stems were included in the swap; we just left both
bikes with the mechanic.

It says "GB" in a circle in a recessed diamond on the stem.

Just above the point of the diamond, an adjusting barrel for the front
brake cable is set in the top of a hole through the stem.

I read somewhere that drilling a hole through the stem is a terrible,
horrible idea, and it makes sense that one should avoid weakening such
a vital component, but it's a tempting idea: It looks neater, it
makes the path of the cable slightly smoother, and it makes the cable
a more convenient place to hang my gloves.

So as long as the hole is there I might as well use it, but the
mechanic at the Trailhouse routes the cable around the stem, as if
there were no hole.

I'm going to have the bike overhauled pretty soon, and I'm thinking of
telling him to use the hole -- but is there some *other* reason why
routing a brale cable through the stem is a bad idea?

--
joy beeson at comcast dot net
http://wlweather.net/PAGESEW/
The above message is a Usenet post.
I don't recall having given anyone permission to use it on a Web site.


If you want to raise or lower a stem with a hole in it to which the front brake cable is anchored then you'd have to adjust the brakes too as lower the stem will move the pads away from the rim and raising the stem will move the pads closer to the rim.

Cheers

Cheers
  #4  
Old April 13th 19, 02:32 PM posted to rec.bicycles.tech
AMuzi
external usenet poster
 
Posts: 13,447
Default A hole in the stem

On 4/13/2019 5:58 AM, Sir Ridesalot wrote:
On Friday, April 12, 2019 at 11:15:09 PM UTC-4, Joy Beeson wrote:
I don't recall whether my handlebars came with the Raleigh Carleton or
the Fugi Grand Tourer -- we swapped components rather suddenly when a
mechanic overhauling the Raleigh found a defect in the brake bridge
that was above his pay grade. I don't think I ever knew whether the
handlebars and stems were included in the swap; we just left both
bikes with the mechanic.

It says "GB" in a circle in a recessed diamond on the stem.

Just above the point of the diamond, an adjusting barrel for the front
brake cable is set in the top of a hole through the stem.

I read somewhere that drilling a hole through the stem is a terrible,
horrible idea, and it makes sense that one should avoid weakening such
a vital component, but it's a tempting idea: It looks neater, it
makes the path of the cable slightly smoother, and it makes the cable
a more convenient place to hang my gloves.

So as long as the hole is there I might as well use it, but the
mechanic at the Trailhouse routes the cable around the stem, as if
there were no hole.

I'm going to have the bike overhauled pretty soon, and I'm thinking of
telling him to use the hole -- but is there some *other* reason why
routing a brale cable through the stem is a bad idea?

--
joy beeson at comcast dot net
http://wlweather.net/PAGESEW/
The above message is a Usenet post.
I don't recall having given anyone permission to use it on a Web site.


If you want to raise or lower a stem with a hole in it to which the front brake cable is anchored then you'd have to adjust the brakes too as lower the stem will move the pads away from the rim and raising the stem will move the pads closer to the rim.



Back when that was the standard setup on MTBs, we saw that
as a feature, not a problem.

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


  #5  
Old April 13th 19, 05:17 PM posted to rec.bicycles.tech
Sir Ridesalot
external usenet poster
 
Posts: 5,270
Default A hole in the stem

On Saturday, April 13, 2019 at 9:32:09 AM UTC-4, AMuzi wrote:
On 4/13/2019 5:58 AM, Sir Ridesalot wrote:

Snipped
If you want to raise or lower a stem with a hole in it to which the front brake cable is anchored then you'd have to adjust the brakes too as lower the stem will move the pads away from the rim and raising the stem will move the pads closer to the rim.



Back when that was the standard setup on MTBs, we saw that
as a feature, not a problem.

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


Until you go to raise that stem and it causes the brake pads to bind against the rim. I remember having that happen a lot on those MTBs that had the hole in the stem with the brake cable going through it.

Cheers
  #6  
Old April 14th 19, 02:09 AM posted to rec.bicycles.tech
jOHN b.
external usenet poster
 
Posts: 2,421
Default A hole in the stem

On Sat, 13 Apr 2019 09:17:34 -0700 (PDT), Sir Ridesalot
wrote:

On Saturday, April 13, 2019 at 9:32:09 AM UTC-4, AMuzi wrote:
On 4/13/2019 5:58 AM, Sir Ridesalot wrote:

Snipped
If you want to raise or lower a stem with a hole in it to which the front brake cable is anchored then you'd have to adjust the brakes too as lower the stem will move the pads away from the rim and raising the stem will move the pads closer to the rim.



Back when that was the standard setup on MTBs, we saw that
as a feature, not a problem.

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


Until you go to raise that stem and it causes the brake pads to bind against the rim. I remember having that happen a lot on those MTBs that had the hole in the stem with the brake cable going through it.

Cheers


Does one raise and lower the handle bars frequently on a MTB? On a
road bike once I have the bike set up to be comfortable I probably
don't change anything, seat height, fore and fat seat position, handle
bar angle or height, etc., for years..
--
cheers,

John B.

  #7  
Old April 14th 19, 02:34 AM posted to rec.bicycles.tech
Sir Ridesalot
external usenet poster
 
Posts: 5,270
Default A hole in the stem

On Saturday, April 13, 2019 at 9:09:44 PM UTC-4, John B. wrote:
On Sat, 13 Apr 2019 09:17:34 -0700 (PDT), Sir Ridesalot
wrote:

On Saturday, April 13, 2019 at 9:32:09 AM UTC-4, AMuzi wrote:
On 4/13/2019 5:58 AM, Sir Ridesalot wrote:

Snipped
If you want to raise or lower a stem with a hole in it to which the front brake cable is anchored then you'd have to adjust the brakes too as lower the stem will move the pads away from the rim and raising the stem will move the pads closer to the rim.


Back when that was the standard setup on MTBs, we saw that
as a feature, not a problem.

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


Until you go to raise that stem and it causes the brake pads to bind against the rim. I remember having that happen a lot on those MTBs that had the hole in the stem with the brake cable going through it.

Cheers


Does one raise and lower the handle bars frequently on a MTB? On a
road bike once I have the bike set up to be comfortable I probably
don't change anything, seat height, fore and fat seat position, handle
bar angle or height, etc., for years..
--
cheers,

John B.


I sometimes change the height of my MTB stem depending on the terrain I'm riding or how much gear/weight I'm carrying. Actually, what I have on my MTB gravel/logging road touring bike with drop bars is a quill adjustable stem.. I set the cables with the stem at the highest point I'd use it and that way I don't have to worry about rubbing brake pads if I raise the stem. I like a more upright position when riding loose surfaces and then lower the stem if I'm doing a lot of distance on pavement. I often have both on my Northern Ontario Canada tours. I ride the pavement to and from the gravel/mining roads I'll be touring and then adjust the stem for the best fit once I'm on the gravel.

Cheers
  #8  
Old April 14th 19, 09:41 AM posted to rec.bicycles.tech
Tosspot[_3_]
external usenet poster
 
Posts: 1,563
Default A hole in the stem

On 14/04/2019 03:09, John B. wrote:
On Sat, 13 Apr 2019 09:17:34 -0700 (PDT), Sir Ridesalot
wrote:

On Saturday, April 13, 2019 at 9:32:09 AM UTC-4, AMuzi wrote:
On 4/13/2019 5:58 AM, Sir Ridesalot wrote:

Snipped
If you want to raise or lower a stem with a hole in it to which the front brake cable is anchored then you'd have to adjust the brakes too as lower the stem will move the pads away from the rim and raising the stem will move the pads closer to the rim.


Back when that was the standard setup on MTBs, we saw that
as a feature, not a problem.

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


Until you go to raise that stem and it causes the brake pads to bind against the rim. I remember having that happen a lot on those MTBs that had the hole in the stem with the brake cable going through it.

Cheers


Does one raise and lower the handle bars frequently on a MTB? On a
road bike once I have the bike set up to be comfortable I probably
don't change anything, seat height, fore and fat seat position, handle
bar angle or height, etc., for years..


Dropper stems :-)

Btw, sig-sep broken?

--space
  #9  
Old April 13th 19, 02:29 PM posted to rec.bicycles.tech
AMuzi
external usenet poster
 
Posts: 13,447
Default A hole in the stem

On 4/12/2019 10:15 PM, Joy Beeson wrote:


I don't recall whether my handlebars came with the Raleigh Carleton or
the Fugi Grand Tourer -- we swapped components rather suddenly when a
mechanic overhauling the Raleigh found a defect in the brake bridge
that was above his pay grade. I don't think I ever knew whether the
handlebars and stems were included in the swap; we just left both
bikes with the mechanic.

It says "GB" in a circle in a recessed diamond on the stem.

Just above the point of the diamond, an adjusting barrel for the front
brake cable is set in the top of a hole through the stem.

I read somewhere that drilling a hole through the stem is a terrible,
horrible idea, and it makes sense that one should avoid weakening such
a vital component, but it's a tempting idea: It looks neater, it
makes the path of the cable slightly smoother, and it makes the cable
a more convenient place to hang my gloves.

So as long as the hole is there I might as well use it, but the
mechanic at the Trailhouse routes the cable around the stem, as if
there were no hole.

I'm going to have the bike overhauled pretty soon, and I'm thinking of
telling him to use the hole -- but is there some *other* reason why
routing a brale cable through the stem is a bad idea?


Yes it's a point of stress concentration on a part not
overly strong and, in the classic era of cast aluminum, your
stem may well have voids or inclusions you can't see.

That said, there's plenty of 'prior art':
http://www.yellowjersey.org/photosfromthepast/am19f.jpg

I've seen plenty of failed cast aluminum stems, old and new:
http://pardo.net/bike/pic/fail-001/FAIL-057.html

which is not to say welded stems are immune:
http://pardo.net/bike/pic/fail-001/FAIL-101.html

but haven't seen an actual failure from a hole drilled in a
stem.

So, yes, it's a bad idea in principle but may be OK in
practice. Given its age (aluminum does age-harden) and the
low cost of a forged or thixoform stem, change it if that
bothers you.
--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


  #10  
Old April 13th 19, 06:30 PM posted to rec.bicycles.tech
Frank Krygowski[_4_]
external usenet poster
 
Posts: 10,538
Default A hole in the stem

On 4/12/2019 11:15 PM, Joy Beeson wrote:


I don't recall whether my handlebars came with the Raleigh Carleton or
the Fugi Grand Tourer -- we swapped components rather suddenly when a
mechanic overhauling the Raleigh found a defect in the brake bridge
that was above his pay grade. I don't think I ever knew whether the
handlebars and stems were included in the swap; we just left both
bikes with the mechanic.

It says "GB" in a circle in a recessed diamond on the stem.

Just above the point of the diamond, an adjusting barrel for the front
brake cable is set in the top of a hole through the stem.

I read somewhere that drilling a hole through the stem is a terrible,
horrible idea, and it makes sense that one should avoid weakening such
a vital component, but it's a tempting idea: It looks neater, it
makes the path of the cable slightly smoother, and it makes the cable
a more convenient place to hang my gloves.

So as long as the hole is there I might as well use it, but the
mechanic at the Trailhouse routes the cable around the stem, as if
there were no hole.

I'm going to have the bike overhauled pretty soon, and I'm thinking of
telling him to use the hole -- but is there some *other* reason why
routing a brale cable through the stem is a bad idea?


The hole causes what's called "stress concentration." That means when
there's a significant load on the stem, stresses will be higher in the
area right around the hole than they would have been without the hole.

Stress concentration is more of a problem for aluminum than for steel,
for reasons I won't go into here (unless asked). But it's not
necessarily a significant problem. Everyone accepts holes in aluminum
hubs (to attach spokes). I have holes drilled in my aluminum frame to
attach shift levers, bottle cages, etc. The problems arise only if the
concentrated stresses are higher than what the metal can resist for the
long term.

I gather from your posts that you're probably not a person who does lots
of high torque pedaling on sprints or tough climbs, where you're yanking
hard on the handlebars. Those yanks would put torque on the stem and
might generate some significant stress. But I doubt you'll see a problem.

More significant, perhaps, is that the hole is already there. If you
don't use the hole it doesn't improve the situation; it's still a stress
concentration. So leaving the cable out of the hole seems silly to me.

So I'd use it as intended. If you want to be super-diligent, check it
once a month to see if any tiny cracks are emanating from it. If you
want to be paranoid, replace the stem.


--
- Frank Krygowski
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Wheel built and tested 32 hole hub, 24 hole rim. James[_8_] Techniques 25 October 23rd 13 10:30 PM
28 hole rim / 36 hole hub stuff Nate Knutson Techniques 13 January 12th 06 08:13 PM
Lacing a 28 hole rim to a 36 hole hub TonyMelton Unicycling 2 May 9th 05 02:42 PM
Lacing 24" 32 or 36 hole Rim to 48 hole Hub pdc Unicycling 8 April 5th 05 09:08 PM
wtb: American Classic Rear road hub 36 hole---will trade for same in 32 hole version jeremyb Marketplace 0 November 8th 04 05:18 PM


All times are GMT +1. The time now is 06:25 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CycleBanter.com.
The comments are property of their posters.