|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
I'm a Transporational Cyclist!
Rather than riding in smoke (which I will still do a little tonight), I've been working on bikes and ebikes. I also bought a bunch of bike stuff including a rack -- attention Frank -- a rack for my commuter. My commuter is a warranty replacement CAADX with oddly placed fender bridge bolts: https://tinyurl.com/y4j7yx63
So, I bent some SS brackets to create stay mounts for my super-cool light weight rack. https://www.wiggle.com/tortec-ultralite-rear-rack. Cheap and rigid and good to 50lbs -- but note that there are no lower hook-spots for the paniers. Ooops. I still have the old Blackburn add-on hooks from the '70s that you stack on the mounting bolt screwed into the dropout eyelet, but alas, my beater commuter bag has spring loaded s-hooks that will not reach down to the eyelet. They will barely get to the tube junction on the rack legs. Waaah. I noted, however, that there were vent holes in the back side of the tubes above the junction, so I tapped those both sides to 5mm (no drilling needed -- hole size was perfect for the tap) and put in a little SS M5 cap screw that acts as a hook. Works perfectly. I'm going to zip tie the dyno wires to my fork and go for a ride with my pannier. The only reason I'm doing this is to justify my slowness. People will not expect me to be fast with my rack, pannier and dyno light. There is nothing in my pannier, but I may fill it with those blow-up bag packing things from the ebike unboxing just to give the impression I'm hauling a load.. -- Jay Beattie. |
Ads |
#2
|
|||
|
|||
I'm a Transporational Cyclist!
On 9/17/2020 9:00 PM, jbeattie wrote:
Rather than riding in smoke (which I will still do a little tonight), I've been working on bikes and ebikes. I also bought a bunch of bike stuff including a rack -- attention Frank -- a rack for my commuter. Congratulations! My commuter is a warranty replacement CAADX with oddly placed fender bridge bolts: https://tinyurl.com/y4j7yx63 Yeah, that's dumb. They ranked creativity above utility. It's from the same school of thought that produces these things: https://www.trendhunter.com/slidesho...vative-bicycle So, I bent some SS brackets to create stay mounts for my super-cool light weight rack. https://www.wiggle.com/tortec-ultralite-rear-rack. Cheap and rigid and good to 50lbs -- but note that there are no lower hook-spots for the paniers. Ooops. I still have the old Blackburn add-on hooks from the '70s that you stack on the mounting bolt screwed into the dropout eyelet, but alas, my beater commuter bag has spring loaded s-hooks that will not reach down to the eyelet. They will barely get to the tube junction on the rack legs. Waaah. I noted, however, that there were vent holes in the back side of the tubes above the junction, so I tapped those both sides to 5mm (no drilling needed -- hole size was perfect for the tap) and put in a little SS M5 cap screw that acts as a hook. Works perfectly. I'm going to zip tie the dyno wires to my fork and go for a ride with my pannier. The only reason I'm doing this is to justify my slowness. People will not expect me to be fast with my rack, pannier and dyno light. There is nothing in my pannier, but I may fill it with those blow-up bag packing things from the ebike unboxing just to give the impression I'm hauling a load. Take pride in your slowness! It's OK as long as you keep moving. -- - Frank Krygowski |
#3
|
|||
|
|||
I'm a Transporational Cyclist!
On Friday, September 18, 2020 at 9:57:27 AM UTC-7, Frank Krygowski wrote:
On 9/17/2020 9:00 PM, jbeattie wrote: Rather than riding in smoke (which I will still do a little tonight), I've been working on bikes and ebikes. I also bought a bunch of bike stuff including a rack -- attention Frank -- a rack for my commuter. Congratulations! My commuter is a warranty replacement CAADX with oddly placed fender bridge bolts: https://tinyurl.com/y4j7yx63 Yeah, that's dumb. They ranked creativity above utility. It's from the same school of thought that produces these things: https://www.trendhunter.com/slidesho...vative-bicycle I think the idea was to eliminate the brake/fender bridge to create ridiculous amounts of clearances. I'm assuming the bosses are strong enough to support a rack. It seems solid. So, I bent some SS brackets to create stay mounts for my super-cool light weight rack. https://www.wiggle.com/tortec-ultralite-rear-rack. Cheap and rigid and good to 50lbs -- but note that there are no lower hook-spots for the paniers. Ooops. I still have the old Blackburn add-on hooks from the '70s that you stack on the mounting bolt screwed into the dropout eyelet, but alas, my beater commuter bag has spring loaded s-hooks that will not reach down to the eyelet. They will barely get to the tube junction on the rack legs. Waaah. I noted, however, that there were vent holes in the back side of the tubes above the junction, so I tapped those both sides to 5mm (no drilling needed -- hole size was perfect for the tap) and put in a little SS M5 cap screw that acts as a hook. Works perfectly. I'm going to zip tie the dyno wires to my fork and go for a ride with my pannier. The only reason I'm doing this is to justify my slowness. People will not expect me to be fast with my rack, pannier and dyno light. There is nothing in my pannier, but I may fill it with those blow-up bag packing things from the ebike unboxing just to give the impression I'm hauling a load. Take pride in your slowness! It's OK as long as you keep moving. -- - Frank Krygowski By the way, I had an old Blackburn rack but the legs were too short for the rack platform to clear the fenders. I also have an abundance of panniers. I used to have a commuter with a rack, but I was content using a backpack the last decade or so, but now my back gets so sore with even the lightest load -- so what the heck, I'll try a rack again. The upside of working on the commuter is that I finally got the levers and bars in exactly the right place. Crappy Nashbar anatomical bars with a slightly odd bend, and it took a lot of fussing. It's still noisy in the BB, and I wish the bike had a threaded BB, but you go with what you get with a warranty replacement. It's raining today -- finally -- and I'm hoping the air cleans up enough for a healthy ride. Last night was lightning and thunder to rival Ohio. One of my earliest memories was watching lightning from the back porch of my great-aunts house in Tiffin. Last night was endless flashes and basically continuous thunder, which is really unusual for Ory-gun. -- Jay Beattie. |
#4
|
|||
|
|||
I'm a Transporational Cyclist!
On 9/18/2020 2:05 PM, jbeattie wrote:
On Friday, September 18, 2020 at 9:57:27 AM UTC-7, Frank Krygowski wrote: On 9/17/2020 9:00 PM, jbeattie wrote: Rather than riding in smoke (which I will still do a little tonight), I've been working on bikes and ebikes. I also bought a bunch of bike stuff including a rack -- attention Frank -- a rack for my commuter. Congratulations! My commuter is a warranty replacement CAADX with oddly placed fender bridge bolts: https://tinyurl.com/y4j7yx63 Yeah, that's dumb. They ranked creativity above utility. It's from the same school of thought that produces these things: https://www.trendhunter.com/slidesho...vative-bicycle I think the idea was to eliminate the brake/fender bridge to create ridiculous amounts of clearances. I'm assuming the bosses are strong enough to support a rack. It seems solid. So, I bent some SS brackets to create stay mounts for my super-cool light weight rack. https://www.wiggle.com/tortec-ultralite-rear-rack. Cheap and rigid and good to 50lbs -- but note that there are no lower hook-spots for the paniers. Ooops. I still have the old Blackburn add-on hooks from the '70s that you stack on the mounting bolt screwed into the dropout eyelet, but alas, my beater commuter bag has spring loaded s-hooks that will not reach down to the eyelet. They will barely get to the tube junction on the rack legs. Waaah. I noted, however, that there were vent holes in the back side of the tubes above the junction, so I tapped those both sides to 5mm (no drilling needed -- hole size was perfect for the tap) and put in a little SS M5 cap screw that acts as a hook. Works perfectly. I'm going to zip tie the dyno wires to my fork and go for a ride with my pannier. The only reason I'm doing this is to justify my slowness. People will not expect me to be fast with my rack, pannier and dyno light. There is nothing in my pannier, but I may fill it with those blow-up bag packing things from the ebike unboxing just to give the impression I'm hauling a load. Take pride in your slowness! It's OK as long as you keep moving. -- - Frank Krygowski By the way, I had an old Blackburn rack but the legs were too short for the rack platform to clear the fenders. I also have an abundance of panniers. I used to have a commuter with a rack, but I was content using a backpack the last decade or so, but now my back gets so sore with even the lightest load -- so what the heck, I'll try a rack again. I tried riding with backpacks way, way back in the beginning. I really disliked it, and thought even a crude Pletscher (sp?) rack was a big improvement. Eventually I settled on Blackburn racks for most bikes. It's raining today -- finally -- and I'm hoping the air cleans up enough for a healthy ride. Last night was lightning and thunder to rival Ohio. One of my earliest memories was watching lightning from the back porch of my great-aunts house in Tiffin. Last night was endless flashes and basically continuous thunder, which is really unusual for Ory-gun. Your climate and mine seem pretty similar if you look at many broad annual averages. But practice, they're quite different. Scary thunderstorms are regular family entertainment here. A huge cycling-related difference is your summer heat is generally dry, while ours is soaked with humidity. Then there's this stuff called snow... -- - Frank Krygowski |
#5
|
|||
|
|||
I'm a Transporational Cyclist!
On Thu, 17 Sep 2020 18:00:11 -0700 (PDT), jbeattie
wrote: There is nothing in my pannier, but I may fill it with those blow-up bag packing things from the ebike unboxing just to give the impression I'm hauling a load. My wire panniers are usually filled with crumpled plastic grocery bags. I didn't take enough on yesterday's ride, and had to economize on the padding when I packed the peppers and corn I'd bought. Sweet Corn Charlie closes for the season tomorrow afternoon. I don't know what I'll do for a mid-week ride now. One can make only so many trips to the teller machine when one is forbidden to go to most of the places where one can spend money. -- Joy Beeson joy beeson at centurylink dot net http://wlweather.net/PAGEJOY/ |
#6
|
|||
|
|||
I'm a Transporational Cyclist!
On Thursday, September 17, 2020 at 6:00:14 PM UTC-7, jbeattie wrote:
Rather than riding in smoke (which I will still do a little tonight), I've been working on bikes and ebikes. I also bought a bunch of bike stuff including a rack -- attention Frank -- a rack for my commuter. My commuter is a warranty replacement CAADX with oddly placed fender bridge bolts: https://tinyurl.com/y4j7yx63 So, I bent some SS brackets to create stay mounts for my super-cool light weight rack. https://www.wiggle.com/tortec-ultralite-rear-rack. Cheap and rigid and good to 50lbs -- but note that there are no lower hook-spots for the paniers. Ooops. I still have the old Blackburn add-on hooks from the '70s that you stack on the mounting bolt screwed into the dropout eyelet, but alas, my beater commuter bag has spring loaded s-hooks that will not reach down to the eyelet. They will barely get to the tube junction on the rack legs. Waaah. I noted, however, that there were vent holes in the back side of the tubes above the junction, so I tapped those both sides to 5mm (no drilling needed -- hole size was perfect for the tap) and put in a little SS M5 cap screw that acts as a hook. Works perfectly. I'm going to zip tie the dyno wires to my fork and go for a ride with my pannier. The only reason I'm doing this is to justify my slowness. People will not expect me to be fast with my rack, pannier and dyno light. There is nothing in my pannier, but I may fill it with those blow-up bag packing things from the ebike unboxing just to give the impression I'm hauling a load.. -- Jay Beattie. Looking for pix of you in the Nevada City https://www.bing.com/images/search?q...geBasi cHover |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Thieving young scum cyclist learns the way of poverty cyclist life | Mr Pounder Esquire | UK | 3 | October 18th 17 03:52 PM |
Cyclist dies in London crash, no wonder when you see the cyclist inthe picture of the scene | MrCheerful | UK | 18 | September 1st 17 09:08 AM |
Hyperbole? not from a cyclist, surely? Pavement cyclist claims aterrorist in a van weapon came near him. | MrCheerful | UK | 15 | September 23rd 16 09:07 PM |
Driver deliberately turns into cyclist and causing cyclist to crash | Bod[_5_] | UK | 6 | October 27th 15 04:26 PM |
Hollywood bus driver attacks cyclist, LAPD handcuffs cyclist | Matt O'Toole | General | 13 | September 29th 07 07:50 PM |