|
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Campagnolo square-taper BB question?
On Jan 26, 10:48*am, Ronko wrote:
In article 285993d5-41d3-4357-9beb- , says... On 26 jan, 08:28, Ronko wrote: The square tapers bottom brackets, specifically Chorus and Record, for approximate years 2000-2006 (10sp alloy) are interchangeable I assume for either Chorus or Record cranks? Yes. And both have rebuildable bearings? No. They use cartidge bearing which are not supposed te be replaced. I did it once, I don't do it again. I replace the whole unit next time. And finally do the Record and Chorus BB have the same bearings or is there a difference? No they are the same. Lou Thanks. What were the issues about replacing the bearings? Had to be pressed off and on? Easy to get off, even the clip on the LH side. It's really hard to get the retaining ring off the RH side w/o deforming it so when you put it back it may interfere with the bearings causing a draggy bearing. I'm batting about 50% when it comes to successfully changing these. |
Ads |
#12
|
|||
|
|||
Campagnolo square-taper BB question?
On 27 Jan, 14:04, Qui si parla Campagnolo wrote:
Thanks. What were the issues about replacing the bearings? Had to be pressed off and on? Easy to get off, even the clip on the LH side. It's really hard to get the retaining ring off the RH side w/o deforming it so when you put it back it may interfere with the bearings causing a draggy bearing. I'm batting about 50% when it comes to successfully changing these. Do the replacements ever get to be replaced or does the spindle break first? |
#13
|
|||
|
|||
Campagnolo square-taper BB question?
Op 27-1-2010 16:40, thirty-six schreef:
On 27 Jan, 14:04, Qui si parla wrote: Thanks. What were the issues about replacing the bearings? Had to be pressed off and on? Easy to get off, even the clip on the LH side. It's really hard to get the retaining ring off the RH side w/o deforming it so when you put it back it may interfere with the bearings causing a draggy bearing. I'm batting about 50% when it comes to successfully changing these. Do the replacements ever get to be replaced or does the spindle break first? Never broke a spindle. Shimano nor Campagnolo. Only use Ultegra/XT and up or Chorus and up. Lou |
#14
|
|||
|
|||
Campagnolo square-taper BB question?
On 27 Jan, 19:57, Lou Holtman wrote:
Op 27-1-2010 16:40, thirty-six schreef: On 27 Jan, 14:04, Qui si parla *wrote: Thanks. What were the issues about replacing the bearings? Had to be pressed off and on? Easy to get off, even the clip on the LH side. It's really hard to get the retaining ring off the RH side w/o deforming it so when you put it back it may interfere with the bearings causing a draggy bearing. I'm batting about 50% when it comes to successfully changing these. Do the replacements ever get to be replaced or does the spindle break first? Never broke a spindle. Shimano nor Campagnolo. Only use Ultegra/XT and up or Chorus and up. So what is the count for repeated bearing replacement on a single axle? |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Campagnolo Carbon Crankset square taper 170mm | [email protected] | Marketplace | 0 | November 8th 08 03:48 PM |
Square taper | [email protected] | Techniques | 13 | February 15th 07 08:00 PM |
Question: 15MM Square Taper Bolt | [email protected] | Techniques | 16 | June 22nd 05 04:56 PM |
FS: NOS Square Taper BBs | Kristan Roberge | Marketplace | 0 | February 17th 05 02:51 PM |
Square Taper BBs | NickZX6R | Australia | 12 | March 24th 04 06:20 AM |