|
|
Thread Tools | Display Modes |
#61
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On Tue, 16 Feb 2016 14:53:27 -0800, sms
wrote: On 2/14/2016 7:03 PM, Jeff Liebermann wrote: On Sun, 14 Feb 2016 16:48:25 -0800 (PST), Sir Ridesalot wrote: I'd like you to post POSITIVE proof that Cygolites are NOT made in the United States. Where's your proof that Cygolites are NOT made in the U.S.A.? Without POSITIVE proof of that, your statment is libel. Thus, where's your proof? Cheers The Cygolite package says "Engineered and Assembled in USA". What that means is that the various components might have been made offshore, but the final assembly is done in the states. It's a common problem. This may help: http://www.forbes.com/sites/timworstall/2013/07/25/googles-moto-x-theres-a-difference-between-made-in-america-and-assembled-in-america/ snip It's very difficult for anything involving Li-Ion batteries, high-power LEDs and various other electronic components to be "Made in the U.S.A." You can screw around with the value you assign to various components of the product in order to jack up the "domestic content" percentage, but that's about it, so "Designed and Assembled in the U.S.A. is about the best that you're going to get. Apple is doing that with the Mac Pro now. Yep. That's especially difficult when there are no domestic component manufacturers for some of the key parts. LiIon is a good example: http://www.atp.nist.gov/eao/wp05-01/chapt2.htm While the R&D and initial production runs are often done in the USA, volume production soon moves offshore. However, I could probably claim a high domestic content if the most expensive and custom parts were all made in the USA. For example, in a bicycle light, the case, mechanical parts, mounting hardware, trim, cosmetics, optics, and possibly the PCB can all be domestically sourced, while the much cheaper commodity parts can be sourced from offshore suppliers. The screwed up part of selling bicycle accessories is that the shops demand Keystone margins (100% mark-up) and you can't sell direct to consumers at less than your MSRP. "Fair Trade" is still alive and well. Once you decide to sell through shops, your retail has to be high enough so you don't lose money on every unit you sell wholesale. Welcome to product marketing. In this case, the product needs to find a compatible buyer. The average impulse bicycle light buyer is NOT going to buy a $400 light at an LBS which could exceed the cost of the bicycle. The typical Amazon shopper is NOT going to buy a $400 light unless he has previously seen, used, and evaluated the product. Each price tier has it's corresponding typical customer. It's also difficult to sell a single product for an odd reason. Most product lines need a loss leader, that nobody buys, but which helps sell the product. In automobiles, it's the overpriced bright red convertible sports car on the showroom floor. Nobody ever buys one, but it attracts the customers, who think of their youthful days of wanting such a car, and end up buying something much cheaper and more practical. Same in bicycle lighting. For example: http://www.trailled.com/lighting/ Price range is from $350 to $1,185 for essentially the same product. If one of the lower priced lights were advertised by itself, it would never sell because few people can justify a $350 head light. However, when compared to the sky high prices of the other lights, $350 looks like a bargain. The $1,185 light is their red convertible and my guess(tm) is they have yet to sell a single one. While Barry can be a little too intense, the light he manufactures and sells is quite good, and he doesn't gouge on spare batteries. How can you tell it's good? Have you seen one in action? Have you looked at his web page and found any test results, specifications, details, reviews, or comparisons with other lights? I haven't and suspect that he's not selling the light on technical merit. He's selling a rather innovative lens system, his connection with NASA, and sheer force of personality. That works very well for selling at county fairs, kiosks, and shows. My guess(tm) is that if Barry produced comparative specs and test data, the light would end up in the middle of the pack with all the other innovative lighting products with nothing to distinguish it from the others. The light would sell pretty well at around $125, but that would mean going 100% direct and forgetting about selling through shops. Agreed, if all he wants to do is sell direct. I don't know the market well enough to determine if direct sales or retail is the optimum approach. Each has their advantages. My best suggestion would be for him to look at the prices of the nearest competitors selling similar lights, and see how well they're doing in direct sales, mail odor, or retail, and then try to steal some of their business. Unless the light does something new and innovative, it's not going to create a new market. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
Ads |
#62
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On 2/17/2016 10:39 AM, Jeff Liebermann wrote:
On Tue, 16 Feb 2016 14:53:27 -0800, sms wrote: On 2/14/2016 7:03 PM, Jeff Liebermann wrote: On Sun, 14 Feb 2016 16:48:25 -0800 (PST), Sir Ridesalot wrote: I'd like you to post POSITIVE proof that Cygolites are NOT made in the United States. Where's your proof that Cygolites are NOT made in the U.S.A.? Without POSITIVE proof of that, your statment is libel. Thus, where's your proof? Cheers The Cygolite package says "Engineered and Assembled in USA". What that means is that the various components might have been made offshore, but the final assembly is done in the states. It's a common problem. This may help: http://www.forbes.com/sites/timworstall/2013/07/25/googles-moto-x-theres-a-difference-between-made-in-america-and-assembled-in-america/ snip It's very difficult for anything involving Li-Ion batteries, high-power LEDs and various other electronic components to be "Made in the U.S.A." You can screw around with the value you assign to various components of the product in order to jack up the "domestic content" percentage, but that's about it, so "Designed and Assembled in the U.S.A. is about the best that you're going to get. Apple is doing that with the Mac Pro now. Yep. That's especially difficult when there are no domestic component manufacturers for some of the key parts. LiIon is a good example: http://www.atp.nist.gov/eao/wp05-01/chapt2.htm While the R&D and initial production runs are often done in the USA, volume production soon moves offshore. However, I could probably claim a high domestic content if the most expensive and custom parts were all made in the USA. For example, in a bicycle light, the case, mechanical parts, mounting hardware, trim, cosmetics, optics, and possibly the PCB can all be domestically sourced, while the much cheaper commodity parts can be sourced from offshore suppliers. The screwed up part of selling bicycle accessories is that the shops demand Keystone margins (100% mark-up) and you can't sell direct to consumers at less than your MSRP. "Fair Trade" is still alive and well. Once you decide to sell through shops, your retail has to be high enough so you don't lose money on every unit you sell wholesale. Welcome to product marketing. In this case, the product needs to find a compatible buyer. The average impulse bicycle light buyer is NOT going to buy a $400 light at an LBS which could exceed the cost of the bicycle. The typical Amazon shopper is NOT going to buy a $400 light unless he has previously seen, used, and evaluated the product. Each price tier has it's corresponding typical customer. It's also difficult to sell a single product for an odd reason. Most product lines need a loss leader, that nobody buys, but which helps sell the product. In automobiles, it's the overpriced bright red convertible sports car on the showroom floor. Nobody ever buys one, but it attracts the customers, who think of their youthful days of wanting such a car, and end up buying something much cheaper and more practical. Same in bicycle lighting. For example: http://www.trailled.com/lighting/ Price range is from $350 to $1,185 for essentially the same product. If one of the lower priced lights were advertised by itself, it would never sell because few people can justify a $350 head light. However, when compared to the sky high prices of the other lights, $350 looks like a bargain. The $1,185 light is their red convertible and my guess(tm) is they have yet to sell a single one. While Barry can be a little too intense, the light he manufactures and sells is quite good, and he doesn't gouge on spare batteries. How can you tell it's good? Have you seen one in action? Have you looked at his web page and found any test results, specifications, details, reviews, or comparisons with other lights? I haven't and suspect that he's not selling the light on technical merit. He's selling a rather innovative lens system, his connection with NASA, and sheer force of personality. That works very well for selling at county fairs, kiosks, and shows. My guess(tm) is that if Barry produced comparative specs and test data, the light would end up in the middle of the pack with all the other innovative lighting products with nothing to distinguish it from the others. The light would sell pretty well at around $125, but that would mean going 100% direct and forgetting about selling through shops. Agreed, if all he wants to do is sell direct. I don't know the market well enough to determine if direct sales or retail is the optimum approach. Each has their advantages. My best suggestion would be for him to look at the prices of the nearest competitors selling similar lights, and see how well they're doing in direct sales, mail odor, or retail, and then try to steal some of their business. Unless the light does something new and innovative, it's not going to create a new market. You never owned a red convertible? Really? Man, you haven't lived. -- Andrew Muzi www.yellowjersey.org/ Open every day since 1 April, 1971 |
#63
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On 2/17/2016 8:39 AM, Jeff Liebermann wrote:
On Tue, 16 Feb 2016 14:53:27 -0800, sms wrote: On 2/14/2016 7:03 PM, Jeff Liebermann wrote: On Sun, 14 Feb 2016 16:48:25 -0800 (PST), Sir Ridesalot wrote: I'd like you to post POSITIVE proof that Cygolites are NOT made in the United States. Where's your proof that Cygolites are NOT made in the U.S.A.? Without POSITIVE proof of that, your statment is libel. Thus, where's your proof? Cheers The Cygolite package says "Engineered and Assembled in USA". What that means is that the various components might have been made offshore, but the final assembly is done in the states. It's a common problem. This may help: http://www.forbes.com/sites/timworstall/2013/07/25/googles-moto-x-theres-a-difference-between-made-in-america-and-assembled-in-america/ snip It's very difficult for anything involving Li-Ion batteries, high-power LEDs and various other electronic components to be "Made in the U.S.A." You can screw around with the value you assign to various components of the product in order to jack up the "domestic content" percentage, but that's about it, so "Designed and Assembled in the U.S.A. is about the best that you're going to get. Apple is doing that with the Mac Pro now. Yep. That's especially difficult when there are no domestic component manufacturers for some of the key parts. LiIon is a good example: http://www.atp.nist.gov/eao/wp05-01/chapt2.htm While the R&D and initial production runs are often done in the USA, volume production soon moves offshore. However, I could probably claim a high domestic content if the most expensive and custom parts were all made in the USA. For example, in a bicycle light, the case, mechanical parts, mounting hardware, trim, cosmetics, optics, and possibly the PCB can all be domestically sourced, while the much cheaper commodity parts can be sourced from offshore suppliers. There was a domestic 18650 manufacturer in Florida at one time. They took over the old GE NiCad business and were doing Li-Ion. http://www.marketwired.com/press-release/electro-energy-receives-first-order-for-us-produced-18650-lithium-ion-batteries-nasdaq-eeei-846281.htm http://www.gainesville.com/article/20150117/ARTICLES/150119704 The screwed up part of selling bicycle accessories is that the shops demand Keystone margins (100% mark-up) and you can't sell direct to consumers at less than your MSRP. "Fair Trade" is still alive and well. Yeah, WTF happened? It was gone for a long time, now you have MAP (Minimum Advertised Price) to try to get around it. Of course it tends to be a losing battle for most product categories and it enables competitors to have a market for products with high margins and low cost of entry. Welcome to product marketing. In this case, the product needs to find a compatible buyer. The average impulse bicycle light buyer is NOT going to buy a $400 light at an LBS which could exceed the cost of the bicycle. The typical Amazon shopper is NOT going to buy a $400 light unless he has previously seen, used, and evaluated the product. Each price tier has it's corresponding typical customer. But the typical Amazon buyer may buy a $125 bicycle light that has a four or five star rating and that is at least shipped by Amazon. How can you tell it's good? Have you seen one in action? Yes. Agreed, if all he wants to do is sell direct. I don't know the market well enough to determine if direct sales or retail is the optimum approach. Each has their advantages. My best suggestion would be for him to look at the prices of the nearest competitors selling similar lights, and see how well they're doing in direct sales, mail odor, or retail, and then try to steal some of their business. Unless the light does something new and innovative, it's not going to create a new market. In my area, there are a lot of Magicshine and Magicshine clones out on the road. They work acceptably well but have their issues. They tend to use the cheapest, lowest-capacity, cells in their 4 cell battery packs. The mount is not the greatest, though it works okay, at least on straight bars. Would someone spending $69.99 on a MJ-808E spend $125 for one of Barry's lights instead? Maybe, if they understood the advantages. |
#64
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On Tuesday, February 16, 2016 at 10:31:41 AM UTC-5, sms wrote:
snip Can the BC21R be charged while the light is on? I don't know. I don't own the BC21R and don't see anything about this in Fenix's literatu http://fenixlight.com/ProductMore.as...3#.VsSpiCArLC0 |
#65
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On Wed, 17 Feb 2016 09:45:58 -0600, AMuzi wrote:
Much interesting material there, but I simply called Cygo, asked for the GM and got a prompt polite response that the product components are USA sourced. I have no reason to doubt him but there's no airtight evidence of that either. Everyone lies, but that's ok because nobody listens. "Complying with the Made in USA Standard" https://www.ftc.gov/tips-advice/business-center/guidance/complying-made-usa-standard Marketers and manufacturers that promote their products as Made in USA must meet the "all or virtually all" standard. "All or virtually all" means that all significant parts and processing that go into the product must be of U.S. origin. That is, the product should contain no or negligible foreign content. Buy American Act - Requires that a product be manufactured in the U.S. of more than 50 percent U.S. parts to be considered Made in USA for government procurement purposes." I would have a problem with any bicycle light that contains a LiIon battery as being 100% domestic content. To the best of my knowledge, there are no domestic LiIon battery manufacturers. Most everything else in the light, including the Cree XM-L2 LED, could be made in the USA. Although the custom plastic parts carry a very low piece price, if amortized tooling and othe front end expenses were included in the parts costs, they might easily be the most expensive parts in the light. Since the battery is a fairly small part of the component cost of the light, "vitually all" is a suitable description. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#66
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On Wed, 17 Feb 2016 10:54:32 -0600, AMuzi wrote:
You never owned a red convertible? Really? Man, you haven't lived. It wasn't mine but does riding around in an antique red fire engine qualify? I also helped restore one, but never got to ride in it. The local Ford dealer has a red convertable something in his showroom window. It's been there for the 40 years I've been in the area. It changes every few years to keep up with the latest model changes. I asked about it (20 years ago) and discovered it's one of the few cars on the lot that are 100% owned by Ford. At the time, the dealer said that he never sold one although the sales people do sometimes take it out for rides and events. Next time I'm near the lot, I'll ask and take some photos. BTW, red convertables allegedly attract police attention and expensive speeding tickets. The paint also tends to fade in sunlight. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#67
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On 2/17/2016 8:49 AM, sms wrote:
You don't see many bicycles with dynamo lights in the U.S., but when you do, the rider almost always has a second light as well (either being carried somewhere, or mounted on the handlebars). More myths from Mr. Scharf. BTW, how would you know the rider has a second light "carried somewhere"? Do you inspect riders' bike bags? I have dynamo lights on five bikes. I have a giveaway coin cell pocket light inside just one of their handlebar bags. It's necessary for three reasons: 1) you need a battery powered light for repairs That can be handy. On the other hand, unless a person is riding way out in the boondocks, there are usually street lamps not far away. 2) you need a higher power light for places where the output of a dynamo light is not sufficient This is the myth that drives the lumen wars. Good quality LED dynamo headlamps produce enough road illumination for at _least_ 20 mph, and that's better than the vast majority of bike headlights. 3) higher-power dynamo lights lack a flash mode and front flashers are the new normal for daytime riding in the U.S., it would be exceedingly foolish to be riding in the daytime without one because vehicles now _expect_ bicyclists to have a flashing DRL. Point number three is a combination of outright lie and absolute bull****. Only a minuscule percentage of American cyclists use front flashing lights in daytime. It's not "the new normal," simply because it's not necessary. It's not even desirable. -- - Frank Krygowski |
#68
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On 2/17/2016 12:12 PM, Gary Young wrote:
On Tuesday, February 16, 2016 at 10:31:41 AM UTC-5, sms wrote: snip Can the BC21R be charged while the light is on? I don't know. I don't own the BC21R and don't see anything about this in Fenix's literatu http://fenixlight.com/ProductMore.as...3#.VsSpiCArLC0 I note that Fenix is attempting to address the problem of dazzling other road users with round beams, i.e. beams not shaped properly for road use. However, their beam shots seem to indicate too much brightness close to the rider. It's better to have an even level of road illumination, which means throwing fewer lumens down close in front of the rider, and progressively more as distance from the rider increases, ending at a horizontal cutoff for most of the beam. Bike headlights with better optics do that, as do auto and motorcycle headlights. -- - Frank Krygowski |
#69
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On 2016-02-17 01:21, Rolf Mantel wrote:
Am 16.02.2016 um 16:31 schrieb sms: A good system would be a dynamo hub charging a USB rechargeable light. It could not keep up at high power, but at least during the day when you're only using the strobe, it could be charging the battery from the dynamo. You can build a dynamo to USB adapter for about $10. Certainly not. If this was a design challenge with a large enough budget I would most certainly take that on. As a product with sufficient volume it can be built for under $10. However, I don't see much of a market for it. ... You know that a dynamo is a 'fixed-power' source not a 'fixed-voltage' source and that therefore it is pretty non-trivial to keep to the USB spec of 'exactly 5V, at most 500mA'. It is not a fixed power source but a more or less constant current source, provided the speed is above a threshold. You can get away need a buck converter and a TVS that caps at some high voltage (tens of volts) in case the load is pulled or is low. Powerful buck switcher ICs under 50 cents can be had from manufacturers such as Richtek, Diodes Inc. and others. You can buy a USB dynamo adapter for $100, ... Way too expensive. ... and you can build one maybe for $30 with the circuits downloadable from the internet, and I do not see much benefit of such a system compared to using standard good dynamo-driven LED lights: only meaningful use might be an additional 'high beam' that you charge during the day and might switch on at night for fast downhill sections. A dynamo-charger plus Li-Ion battery would make a lot of sense on a bicycle but the industry is asleep at the wheel when it comes to stuff like this. So we have to build our own systems. I don't have a dynamo because they aren't popular here in the US and I don't like to spoke up a new front wheel. So I have a 60 watt-hour Li-Ion battery and this allows 5h rides with the front light on full bore most of the time, much brighter than any dynamo light can ever be. When I return home and park the bike in the garage it gets plugged in and recharged. It has a charge port under the seat. -- Regards, Joerg http://www.analogconsultants.com/ |
#70
|
|||
|
|||
Lights = manufacturers moving to non-replaceable batteries
On 2/17/2016 11:47 AM, Jeff Liebermann wrote:
On Wed, 17 Feb 2016 10:54:32 -0600, AMuzi wrote: You never owned a red convertible? Really? Man, you haven't lived. It wasn't mine but does riding around in an antique red fire engine qualify? I also helped restore one, but never got to ride in it. The local Ford dealer has a red convertable something in his showroom window. It's been there for the 40 years I've been in the area. It changes every few years to keep up with the latest model changes. I asked about it (20 years ago) and discovered it's one of the few cars on the lot that are 100% owned by Ford. At the time, the dealer said that he never sold one although the sales people do sometimes take it out for rides and events. Next time I'm near the lot, I'll ask and take some photos. BTW, red convertables allegedly attract police attention and expensive speeding tickets. The paint also tends to fade in sunlight. Ask me how I know that. Oh, and yes modern red pigments suck all around, it's the one color that hasn't kept up in paint progress. -- Andrew Muzi www.yellowjersey.org/ Open every day since 1 April, 1971 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cheap lights using CR123 batteries | Tom Anderson | UK | 3 | January 18th 11 02:33 AM |
Replaceable vs. non-replaceable derailer hangers | Paul Myron Hobson | Techniques | 19 | December 8th 07 08:30 AM |
Rechargable Cells/batteries for Lights | Keiron Kinninmont | Techniques | 8 | December 25th 06 11:58 PM |
Lights without batteries? | Steve Watkin | UK | 9 | May 16th 06 10:04 PM |
Rechargeable batteries with LED lights | David Ward | Techniques | 8 | March 17th 05 03:40 AM |